Hyundai Accent Manuals

Hyundai Accent: Tightening Torque Table Of Standard Parts - General InformationHyundai Accent: Tightening Torque Table Of Standard Parts

Hyundai Accent RB (2010-2018) Service Manual / General Information / Tightening Torque Table Of Standard Parts

 
Bolt nominal
diameter (mm)
Pitch (mm)
Torque Nm (kg.cm, lb.ft)
Head Mark 4
Head Mark 7

M5
0.8
3 ~ 4 (30 ~ 40, 2.2 ~ 2.9)
5 ~ 6 (50 ~ 60, 3.6 ~ 4.3)
M6
1.0
5 ~ 6 (50 ~ 50, 3.6 ~ 4.3)
9 ~ 11 (90 ~ 110, 6.5 ~ 8.0)
M8
1.25
12 ~ 15 (120 ~ 150, 9 ~ 11)
20 ~ 25 (200 ~ 250, 14.5 ~ 18.0 )
M10
1.25
25 ~ 30 (250 ~ 300, 18 ~ 22)
30 ~ 50 (300 ~ 500, 22 ~ 36)
M12
1.25
35 ~ 45 (350 ~ 450, 25 ~ 33)
60 ~ 80 (600 ~ 800, 43 ~ 58)
M14
1.5
75 ~ 85 (750 ~ 850, 54 ~ 61)
120 ~ 140 (1,200 ~ 1,400, 85 ~ 100)
M16
1.5
110 ~ 130 (1,100 ~ 1,300, 80 ~ 94)
180 ~ 210 (1,800 ~ 2,100, 130 ~ 150)
M18
1.5
160 ~ 180 (1,600 ~ 1,800, 116 ~ 130)
260 ~ 300 (2,600 ~ 3,000, 190 ~ 215)
M20
1.5
220 ~ 250 (2,200 ~ 2,500, 160 ~ 180)
360 ~ 420 (3,600 ~ 4,200, 260 ~ 300)
M22
1.5
290 ~ 330 (2,900 ~ 3,300, 210 ~ 240)
480 ~ 550 (4,800 ~ 5,500, 350 ~ 400)
M24
1.5
360 ~ 420 (3,600 ~ 4,200, 260 ~ 300)
610 ~ 700 (6,100 ~ 7,000, 440 ~ 505)

1.
The torques shown in the table are standard values under the following conditions.
•
Nuts and bolts are made of galvanized steel bar.
•
Galvanized plain steel washers are inserted.
•
All nuts, bolts and plain washers are dry.
2.
The torques shown in the table are not applicable.
•
When spring washers, toothed washers and the like are inserted.
•
If plastic parts are fastened.
•
If self-tapping screws or self-locking nuts are used.
•
If threads and surfaces are coated with oil.
3.
Reduce the torque values to the indicated percentage of the standard value under the following conditions.
•
If spring washers are used : 85%
•
If threads and bearing surfaces are stained with oil : 85%
Emergency Towing
There are three popular methods of towing a vehicle : - The operator loads the vehicle on the back of truck. This is best way of transporting the vehicle. ...

Meaning Of Symbols
There are five primary symbols used to complement illustrations. These symbols indicate the part to apply such materials during service.   Symbol Meaning ...

See also:

Installation
1. Installation is the reverse of removal. • ...

Inspection
Battery Diagnostic Flow Vehicle parasitic current inspection 1. Turn the all electric devices OFF, and then turn the ignition switch OFF. ...

Rear Wheel Alignment
When using a commercially available computerized wheel alignment equipment to inspect the rear wheel alignment, always position ...

Hyundai Accent Manuals


© 2011-2024 Copyright www.hamanual.com