The Micro 570 Analyzer (Canada only)
※ Because of the possibility of personal injury,
always use extreme caution and appropriate eye protection when working
with batteries.
※ When charging battery by test result, Battery must
be fully charged.
To get accurate test result, battery surface voltage
must have subsided ahead before test when you test battery after charged.
(See following Battery Test Results)
|
1. |
Connect the tester to the battery.
|
2. |
The tester will ask if the battery is connected "IN-VEHICLE"
or "OUT-OF-VEHICLE". Make your selection by pressing the arrow buttons;
then press ENTER.
|
3. |
Select CCA and press the ENTER button.
|
4. |
Set the CCA value displayed on the screen to the
CCA value marked on the battery label by pressing up and down buttons
and press ENTER.
|
5. |
The tester will conduct battery test.
|
6. |
The tester displays battery test results including
voltage and battery ratings.
Refer to the following table and take the appropriate
action as recommended by the Micro 570.
Battery Test Results
[Charge and Retest method after battery charge]
Battery charge
Set battery charger to ‘Auto Mode’ (The Mode that
charging current drops as the battery charges.) and charge battery until
charging current down close to zero or the charger alerts you with an
alarm when charge is complete.
(Minimum charging time recommended: More than 3 hours
with Auto Mode that explained above)
Battery Test after charge
Do not test battery right after the charge. Test
battery after battery surface voltage has subsided as instructed in
the following procedure.
Starter Test Procedure
|
7. |
After the battery test, press ENTER immediately for
the starter test.
|
8. |
Start the engine.
|
9. |
Cranking voltage and starter test results will be
displayed on the screen.
Refer to the following table and take the appropriate
action as recommended by the Micro 570.
Starter Test Results
Charging System Test Procedure
|
10. |
Press ENTER to begin charging system test.
|
11. |
The tester displays the actual voltage of alternator.
Press ENTER to continue.
|
12. |
Turn off all electrical load and rev engine for 5
seconds with pressing the accelerator pedal. (Follow the instructions
on the screen)
|
13. |
The message that engine RPM is detected will be displayed
on the screen. Press ENTER to continue.
|
14. |
If the engine RPM is not detected, press ENTER after
revving engine.
|
15. |
The tester will conduct charging system test during
loads off.
|
16. |
Turn on electrical loads (air conditioner, lamps,
audio and etc). Press ENTER to continue.
|
17. |
The tester will conduct charging system test during
loads on.
|
18. |
Rev engine for 5 seconds with pressing the accelerator
pedal. (Follow the instructions on the screen)
|
19. |
The message that engine RPM is detected will be displayed
on the screen. Press ENTER to continue.
|
20. |
If the engine RPM is not detected, press ENTER after
revving engine.
|
21. |
Turn off electrical loads (air conditioner, lamps,
audio and etc). Turn the engine off.
|
22. |
Charging voltage and charging system test results
will be displayed on the screen.
Shut off engine end disconnect the tester clamps
from the battery. Refer to the following table and take the appropriate
action as recommended by the Micro 570.
Charging System Test Results
|
Transmitter precautions
NOTICE
The transmitter will not work if any of following occur:
The ignition key is in ignition switch.
You exceed the operating distance limit (about 90 feet [30 m]).
The battery in the tra ...
Air bag - advanced supplemental restraint system
(1) Driver’s front air bag
(2) Passenger’s front air bag
(3) Side impact air bag
(4) Curtain air bag
WARNING
Even in vehicles with air bags, you and your passengers must always wear
the ...
Overdrive Clutch Control Solenoid Valve(OD/C_VFS). Description and Operation
Description
Overdrive clutch control solenoid valve(OD/C_VFS) is attached to the valve
body. This variable force solenoid valve directly controls the hydraulic pressure
inside the overdrive ...