Hyundai Accent Manuals

Hyundai Accent: Removal - Timing Chain. Repair procedures - Timing System. - Engine Mechanical SystemHyundai Accent: Removal

Engine removal is not required for this procedure.
Use fender covers to avoid damaging painted surfaces.
To avoid damage, unplug the wiring connectors carefully while holding the connector portion.
Mark all wiring and hoses to avoid misconnection.
In case of removing the high pressure fuel pump, high pressure fuel pipe, delivery pipe, and injector, there may be injury caused by leakage of the high pressure fuel. So don’t do any repair work right after engine stops.
1.
Remove the engine cover.
2.
Disconnect the battery negative terminal (A).

3.
Remove the air cleaner assembly.
(1)
Remove the air duct (A).
(2)
Disconnect the breather hose (B) and air intake hose (C).
(3)
Remove the air cleaner assembly (D).

4.
Remove the RH front wheel.
5.
Remove the under covers (A).

6.
Disconnect the A/C compressor switch connector (A), the alternator connector (B) and the cable from the alternator “B” terminal (C).

7.
Disconnect the intake OCV (Oil control valve) connector (A) and the exhaust OCV (Oil control valve) connector (B).

8.
Disconnect the ignition coil connectors (A), the injector extension connector (B), the VIS (Variable intake system) connector (C) and the PCSV (Purge control solenoid valve) connector (D).

9.
Disconnect the FPCV (Fuel pressure control valve) connector (A), the intake CMPS (Camshaft position sensor) connector (B), the exhaust CMPS (Camshaft position sensor) connector (C), the front oxygen sensor connector (D), the rear oxygen sensor connector (E) and the condenser connector (F).

10.
Disconnect the oxygen sensor connectors (A) and the condenser connector (B).

11.
Disconnect the fuel hose (A) and the PCV (Positive crankcase ventilation) hose (B).

12.
Remove the vacuum pipe assembly (A).

13.
Remove the high pressure pipe (A). (Refer to FL group)

14.
Remove the high pressure fuel pump (A) and the roller tappet (B). (Refer to FL group)

15.
Remove the ignition coils (A).

16.
Remove the exhaust OCV (Oil control valve) (B).

17.
Remove the cylinder head cover (A) with gaskets (B).

18.
Remove the exhaust OCV (Oil control valve) adapter (A).

19.
Loosen the water pump pulley bolt and the drive idler mounting bolt.
20.
Loosen the alternator tension adjusting bolt (A) to loosen tension.

21.
Remove the alternator drive belt (A).

22.
Remove the alternator (A).

23.
Disconnect the ground cable (A) and remove the engine mounting support bracket (B).

Support the engine with a jack not to be tilted.
24.
Remove the alternator bracket (B).
25.
Remove the engine support bracket (A).

26.
Remove the water pump pulley (A) and the drive belt idler (B).

27.
Remove the water pump (A).

28.
Turn the crankshaft pulley clockwise, and align its groove with the timing mark of the timing chain cover.

29.
Remove the crankshaft bolt (B) and crankshaft pulley (A).

30.
Remove the timing chain cover (A).

There are two methods to hold the ring gear when installing or removing the crankshaft damper pulley.
Install the SST (09231-2B100) to hold the ring gear after removing the starter.

Install the SST (09231-3D100) to hold the ring gear after removing the dust cover.
1.
Remove the bracket (A).

2.
Remove the dust cover (A) and unfasten the transaxle mounting bolt (B).

3.
Adjust the length of the holder nuts (A) so that the front plate of the holder (B) puts in the ring gear (C) teeth.
4.
Adjust the angle of the links (D), and fasten the bolt 70mm(2.7559in) in the original mounted hole.

5.
Tighten the bolts and nuts of the holder and links securely.

31.
Align the timing marks of the CVVT sprockets with the upper surface of the cylinder head to make No.1 cylinder be positioned at TDC.
(1)
Check the dowel pin of the crankshaft for facing upside of the engine at this monent.
Put paint marks on the timing chain links(3 places) that meet with the timing marks of the CVVT sprockets(In, Ex : 2) and the CVVT sprocket.

32.
Remove the hydraulic tensioner (A).

Before removing the tensioner, fix the piston of the tensioner with a pin through the hole(B) at compressed position.
33.
Remove the timing chain tensioner arm (A) and guide (B).

34.
Remove the timing chain (A).


Timing Chain. Repair procedures
...

Inspection
Sprockets, Hydraulic Tensioner, Chain Guide, Tensioner Arm 1. Check the CVVT sprocket, crankshaft sprocket teeth for abnormal wear, cracks or damage. Repla ...

See also:

Components and Components Location
Components [Sedan] 1. Front seat belt 2. Height adjuster 3. Front seat belt anchor pretensioner 4. Rear seat belt 5. Rear center seat belt 6. Rear ...

Driver Airbag (DAB) Module and Clock Spring. Description and Operation
Description Driver Airbag (DAB) is installed in the steering wheel and electrically connected to SRSCM via the clock spring. It protects the driver by deploying the airbag when frontal crash ...

Alternator. Components and Components Location
Components 1. Nut 2. Pulley 3. Spacer 4. Front bracket 5. Front bearing 6. Stator 7. Rotor 8. Rear bearing 9. Rear bracket 10. Brush holder assem ...

Hyundai Accent Manuals


© 2011-2024 Copyright www.hamanual.com