Hyundai Accent Manuals

Hyundai Accent: Rear Torsion Beam Axle. Repair procedures - Rear Suspension System - Suspension SystemHyundai Accent: Rear Torsion Beam Axle. Repair procedures

Hyundai Accent RB (2010-2018) Service Manual / Suspension System / Rear Suspension System / Rear Torsion Beam Axle. Repair procedures

Replacement

[Disc Type]
1.
Remove the rear wheel & tire.
Tightening torque :
88.3 ~ 107.9N.m(9.0 ~ 11.0kgf.m, 65.1 ~ 79.6lb-ft)

Be careful not to damage to the hub bolts when removing the rear wheel & tire.
2.
Remove the clip (A) and then remove the parking brake cable (B).
3.
Remove the parking brake clip (A).
4.
Loosen the bolt & nut and then remove the parking brake cable (A) & wheel speed sensor cable (B) from the torsion beam axle.
5.
Remove the brake caliper assembly (B) from the torsion beam axle by loosening the bolts (A).
Tightening torque :
63.7 ~ 73.5N.m(6.5 ~ 7.5kgf.m, 47.0 ~ 54.2lb-ft)

6.
Loosen the bolt & nut and then remove the rear shock absorber (A) from the torsion beam axle (B).
Tightening torque :
98.1 ~ 117.7N.m (10.0 ~ 12.0kgf.m, 72.3 ~ 86.8lb-ft)

7.
Remove the torsion axle (A) from the body loosening the bolts.
Tightening torque :
98.1 ~ 117.7N.m (10.0 ~ 12.0kgf.m, 72.3 ~ 86.8lb-ft)

8.
Installation is the reverse of removal.
[Drum Type]
1.
Remove the rear wheel & tire.
Tightening torque :
88.3 ~ 107.9N.m (9.0 ~ 11.0kgf.m, 65.1 ~ 79.6lb-ft)

2.
Loosen the screw (A) and then remove the disc (B).
Tightening torque :
4.9 ~ 5.9N.m (0.5 ~ 0.6kgf.m, 3.6 ~ 4.3lb-ft)

3.
Remove the spring(A, B, C).
4.
Remove the shoe (A).
5.
Disconnect the parking brake cable (A) from lining (B).
6.
Remove the clip (A).
7.
Remove the parking brake cable clip (A).
8.
Loosen the wheel speed sensor cable (A) bolt &nut and parking brake cable (B) mounting nut.
9.
Remove the brake hose (A) and then loosen the cylinder bolt.
10.
Loosen the hub mounting bolt and then remove the hub (A) from the torsion beam (B).
Tightening torque :
49.0 ~ 58.8N.m (5.0 ~ 6.0kgf.m, 36.2 ~ 43.4lb-ft)

11.
Loosen the bolt & nut and then remove the rear shock absorber (A) from the torsion beam axle (B).
Tightening torque :
98.1 ~ 117.7N.m (10.0 ~ 12.0kgf.m, 72.3 ~ 86.8lb-ft)

12.
Loosen the bolt and then remove the torsion beam axle (A) from the body.
Tightening torque :
98.1 ~ 117.7N.m (10.0 ~ 12.0kgf.m, 72.3 ~ 86.8lb-ft)

13.
Install in the reverse order of removal.

Rear Torsion Beam Axle. Components and Components Location
Components 1. Rear torsion beam axle ...

Tires/Wheels
...

See also:

Intake Manifold. Components and Components Location
Components 1. Intake manifold 2. Intake manifold gasket 3. Electronic throttle body gasket 4. Electronic throttle body 5. Bracket ...

Economical operation
Your vehicle's fuel economy depends mainly on your style of driving, where you drive and when you drive. Each of these factors affects how many miles (kilometers) you can get from a gallon (l ...

Ignition switch position
LOCK The steering wheel locks to protect against theft (if equipped). The ignition key can be removed only in the LOCK position. When turning the ignition switch to the LOCK position, push the k ...

Hyundai Accent Manuals

В© 2011-2026 Copyright www.hamanual.com