Hyundai Accent: Removal

Hyundai Accent RB (2010-2018) Service Manual / Manual Transaxle System (M6CF1) / Manual Transaxle System / Manual Transaxle. Repair procedures / Removal

1.

Remove the following items;

A.	Engine cover (A). (Refer to "Intake and Exhaust system" in EM group)

B.	Air cleaner assembly (B) and air duct (C) . (Refer to "Intake and Exhaust system" in EM group)

C.	Battery and battery tray (D). (Refer to "Charging system" in EE group)

D.	ECM (E). (Refer to "Engine Control System" in FL group)

2.	Disconnect the vehicle speed sensor connector (A).

3.	Remove the back up lamp switch connector (B).

4.	Remove the ground cable from transaxle (A).

5.	Disconnect the shift cable bracket bolts (B-3ea) after removing the washer and pin (A).

6.

Remove the tube bracket bolt (A).

Tightening torque:

14.7 ~ 21.6 N.m (1.5 ~ 2.2 kgf.m, 10.8 ~ 15.9 lb-ft)

7.

Remove the transaxle upper mounting bolt (B-2ea) and the start motor mounting bolt (A-2ea).

Tightening torque:

(A,B) 42.2 ~ 54.0 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)

8.	Remove the hood assembly. (Refer to "Exterior (hood)" in BD group.)

9.	Remove the cowl top cover. (Refer to "Interior(cowl top cover)" in BD group.)

10.	Remove the wiper motor. (Refer to "Windshield Wiper motor" in BE group.)

11.	Remove the cowl complete assembly panel (A).

12.	Using the engine support fixture (Support SST No.: 09200-2S200, Adapter SST No.: 09200-2S100, Beam SST No.: 09200-38001/3N000), hold the engine and transaxle assembly safely.

13.	Remove the mounting cover (A).

14.

Remove the transaxle support mounting bracket bolts (A-2ea).

Tightening torque:

88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

15.

Remove the transaxle support mounting bracket (A).

Tightening torque:

58.9 ~ 78.5 N.m (6.0 ~ 8.0 kgf.m, 43.4 ~ 57.9 lb-ft)

16.	Remove the under cover (A).

17.	Remove the drive shaft assembly. (Refer to "Drive shaft assembly" in DS group.)

18.

Remove the clutch release cylinder assembly (B) after removing the nuts (A-2ea).

Tightening torque:

14.7 ~ 21.6 N.m (1.5 ~ 2.2 kgf.m, 10.8 ~ 15.9 lb-ft)

19.

Remove the roll rod support bracket (C) after removing bolt (A,B).

Tightening torque:

(A) 49.0 ~ 68.6 N.m (5.0 ~ 7.0 kgf.m, 36.2 ~ 50.6 lb-ft)

(B) 107.9 ~ 127.5 N.m (11.0 ~ 13.0 kgf.m, 79.6 ~ 94.1 lb-ft)

20.	Remove the drive shaft cover (A).

21.	Remove the brackets (A).

22.

Remove the lower mounting bolts (A-3ea, B-2ea) of lower part of the transaxle, and the left side cover and remove the transaxle assembly by supporting it with a jack.

Be careful not to damage other system or parts near by when removing the engine and transaxle assembly.

Tightening torque:

(A) 43 ~ 49 N.m (4.3 ~ 4.9 kgf.m, 31.1 ~ 35.4 lb-ft)

(B) 43 ~ 55 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)

Manual Transaxle. Repair procedures

...

Installation

1. Installation is the reverse of removal. • ...

See also:

General
1. Basically, all measurements in this manual are taken with a tracking gauge. 2. When a measuring tape is used, check to be sure there is ...

Maintenance under severe usage conditions
The following items must be serviced more frequently on cars normally used under severe driving conditions. Refer to the chart below for the appropriate maintenance intervals. R : Replace I : I ...

Installation
1. Installation is the reverse of removal. • ...

Hyundai Accent Manuals

© 2011-2026 Copyright www.hamanual.com