Hyundai Accent Manuals

Hyundai Accent: Front Seat Belt. Repair procedures - Seat Belt - Body (Interior and Exterior)Hyundai Accent: Front Seat Belt. Repair procedures

Hyundai Accent RB (2010-2018) Service Manual / Body (Interior and Exterior) / Seat Belt / Front Seat Belt. Repair procedures

Replacement

Front Seat Belt Replacement
•
When installing the belt, make sure not to damaged the pretensioner.
1.
Remove the following items first.
A.
Front seat assembly
(Refer to the BD group – “Front Seat”).
B.
Front door scuff trim and rear door scuff trim
(Refer to the BD group – “Interior Trim”).
2.
Disconnect the battery negative cable, and wait for at least three minutes before beginning work.
3.
The seat belt anchor pretensioner (A) be removed after pushing the lock pin (B) as arrow direction.
4.
Using a screwdriver or remover, remove the center pillar lower trim (A).
5.
After loosening the mounting bolt, then remove the center pillar upper trim (A).
6.
Loosen the mounting bolt, then remove the front seat belt upper anchor (A).
Tightening torque :
39.2~53.9 N.m (4.0~5.5 kgf.m, 28.9~39.8 lb-ft)

7.
After disconnecting the pretensioner connector lock pin, remove the BPT connector (A), Loosening the mounting bolt, then remove the pretensioner (B).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)

8.
Installation is the reverse of removal.
Hight Adjuster Replacement
1.
Remove the following items first:
A.
Front door scuff trim and rear door scuff trim
(Refer to the BD group – “Interior Trim”).
B.
Front seat belt lower anchor.
C.
Center pillar lower trim.
(Refer to the BD group – “Interior Trim”).
D.
Center pillar upper trim
(Refer to the BD group – “Interior Trim”).
E.
Front seat belt upper anchor.
2.
After loosening the bolts, then remove the hight adjustor (A).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)

3.
Installation is the reverse of removal.
•
Replace any damaged clips.
•
Make sure the height adjust properly.
Front Seat Belt Buckle Replacement
1.
Remove the following items first:
A.
Front seat assembly
(Refer to the BD group – “Front Seat”).
2.
After loosening the mounting screws, then remove the front seat track side cover (A).
3.
Disconnect the connect (A) mounting clip.
4.
After loosening the mounting bolt, then remove the front seat belt buckle (A).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)

5.
Installation is the reverse of removal.

Components and Components Location
Components [Sedan] 1. Front seat belt 2. Height adjuster 3. Front seat belt anchor pretensioner 4. Rear seat belt 5. Rear center seat belt 6. Rear ...

Rear Seat Belt. Repair procedures
Replacement Rear Seat Belt Replacement [Sedan] • When installing the belt, make s ...

See also:

Installation
1. Connect the audio unit connectors and cable. 2. Install the audio unit. 3. Install the crash pad center fas ...

General Information
The Micro 570 Analyzer (Canada only) The Micro 570 Analyzer provides the ability to test the charging and starting systems, including the battery, starter and alternator. ...

Limp Home Function
1. Limp Home By Tester If the PCM (ECM) detects the fault of the SMARTRA or transponder, the PCM (ECM) will allow limp home function of the immobilizer. Limp h ...

Hyundai Accent Manuals


© 2011-2024 Copyright www.hamanual.com