Hyundai Accent: Repair procedures
Hyundai Accent RB (2010-2018) Service Manual / Engine Electrical System / Starting System / Repair procedures
Troubleshooting
| Starter Circuit |
The battery must be in good condition and fully charged.
|
| 1. |
Remove the fuel pump relay(A) from the fuse box.
|
| 2. |
With the shift lever in N or P (A/T) or clutch pedal
pressed (M/T), turn the ignition switch to "START"
If the starter normally cranks the engine, starting
system is OK. If the starter will not crank the engine at all, go to
next step.
If it won't disengage from the ring gear when you
release key, check for the following until you find the cause.
|
| 3. |
Check the battery condition. Check electrical connections
at the battery, battery negative cable connected to the body, engine
ground cables, and the starter for looseness and corrosion. Then try
starting the engine again.
If the starter cranks normally the engine, repairing
the loose connection repaired the problem. The starting system is now
OK.
If the starter still does not crank the engine, go
to next step.
|
| 4. |
Disconnect the connector from the S-terminal of solenoid.
Connect a jumper wire from the B-terminal of solenoid to the S-terminal
of solenoid.
For safety reasons, perform the test under the condition
stated in item 2, "With the shift lever in N or P (A/T), or clutch pedal
pressed (M/T)".
Pay sufficient attention to safety, by using parking
brake, car lock, etc.
If the starter cranks the engine, go to next step.
If the starter still does not crank the engine, remove
the starter, and repair or replace as necessary.
|
| 5. |
Check the following items in the order listed until
you find the open circuit.
|
Starter Solenoid Test
| 1. |
Disconnect the lead wire from the M-terminal of solenoid
switch.
|
| 2. |
Connect the battery as shown. If the starter pinion
pops out, it is working properly. To avoid damaging the starter, do
not leave the battery connected for more than 10 seconds.
|
| 3. |
Disconnect the battery from the M terminal.
If the pinion does not retract, the hold-in coil
is working properly. To avoid damaging the starter, do not leave the
battery connected for more than 10 seconds.
|
| 4. |
Disconnect the battery also from the body. If the
pinion retracts immediately, it is working properly. To avoid damaging
the starter, do not leave the battery connected for more than 10 seconds.
|
Free Running Test
| 1. |
Place the starter motor in a vise equipped with soft
jaws and connect a fully-charged 12-volt battery to starter motor as
follows.
|
| 2. |
Connect a test ammeter (150-ampere scale) and carbon
pile rheostats shown is the illustration.
|
| 3. |
Connect a voltmeter (15-volt scale) across starter
motor.
|
| 4. |
Rotate carbon pile to the off position.
|
| 5. |
Connect the battery cable from battery's negative
post to the starter motor body.
|
| 6. |
Turn on the switch connected between S-terminal and
B-terminal, and adjust by carbon pile until battery voltage shown on
the voltmeter reads 11 volts.
|
| 7. |
Confirm that the maximum amperage is within the specifications
and that the starter motor turns smoothly and freely.
|
Description and Operation
Description
The starting system includes the battery, starter, solenoid
switch, inhibitor switch (A/T), ignition switch, ignition lock switch, connection
wires and the battery cable.
Whe ...
Starter. Components and Components
Location
Components
1. Screw
2. Front bracket
3. Stop ring
4. Stopper
5. Overrun clutch
6. Lever
7. Lever plate
8. Lever packing
9. Magnet switch
10. Arma ...
See also:
Removal
1.
Remove the battery and the battery tray.
(Refer to "Charging system" in EE group.)
2.
Remove the under cover (A).
...
To cancel cruise control, do one of the following
Press the brake pedal.
Press the clutch pedal with a manual transaxle.
Shift the shift lever into N (Neutral) with an automatic transaxle
Press the CANCEL switch located on the steering whe ...
Rail Pressure Sensor (RPS). Troubleshooting
Signal Waveform
...
Hyundai Accent Manuals
В© 2011-2024 Copyright www.hamanual.com