Hyundai Accent Manuals

Hyundai Accent: Removal - Shift Lever. Repair procedures - Automatic Transaxle Control System - Automatic Transaxle SystemHyundai Accent: Removal

Hyundai Accent RB (2010-2018) Service Manual / Automatic Transaxle System / Automatic Transaxle Control System / Shift Lever. Repair procedures / Removal

Shift Lever Assembly Replacement
1.
Remove the center console.
(Refer to "interior (console)" in BD group)
2.
Disconnect the connector (A).

3.
Remove the control cable (B).
4.
Remove the shift lock cable (C) and key lock cable (B) by removing the nuts (A-2ea).
Tightening torque:
9.8 ~ 14.7 N.m (1.0 ~ 1.5 kgf.m, 7.2 ~ 10.8 lb-ft)

5.
Remove the shift lever assembly (A) by removing the bolts (B-4ea).
Tightening torque:
9.8 ~ 14.7 N.m (1.0 ~ 1.5 kgf.m, 7.2 ~ 10.8 lb-ft)

6.
Installation is the reverse of removal.
Make sure vehicle does not roll before setting room side shift lever and T/M side manual control lever to "N" position.
Control Cable Assembly Replacement
1.
Remove the center console.
(Refer to "interior (console)" in BD group)
2.
Remove the control cable (B).
3.
Remove the retainer (A) and nuts (B).
Tightening torque:
9.8 ~ 14.7 N.m (1.0 ~ 1.5 kgf.m, 7.2 ~ 10.8 lb-ft)

4.
Remove the nut (A) from the manual control lever.
5.
Remove the control cable (B) from the bracket (C) at transaxle assembly side.
(Refer to "Automatic Transaxle" in this group)
Tightening torque:
9.8 ~ 14.7 N.m (1.0 ~ 1.5 kgf.m, 7.2 ~ 10.8 lb-ft)

6.
Remove the control cable at cabin room.
7.
Installation is the reverse of removal.
•
Set room side AT lever(shift lever) and automatic transaxle side manual control lever to "N" position.
•
Control cable must be free unreasonable bending.
Shift Lock Cable Replacement
1.
Remove the center console.
(Refer to "interior(console)"in BD group)
2.
Remove the shift lock cable (A).
Tightening torque:
8.8 ~ 13.7 N.m (0.9 ~ 1.4 kgf.m, 6.5 ~ 10.1 lb-ft)

3.
Remove the shift lock cable (B) from the brake pedal (A).
4.
Installation is the reverse of removal.
Shift lock cable must not have any bending.

Shift Lever. Repair procedures
...

Adjustment
Adjusting the control cable 1. Set room side AT lever(shift lever) and automatic transaxle side manual control lever to "N" position. 2. ...

See also:

Rear Door. Components and Components Location
Components 1. Rear door trim 2. Rear door seal 3. Rear door panel 4. Rear door delta inner cover 5. Rear door channel 6. Rear door belt inside weatherstrip 7. ...

Removal
1. Turn the ignition switch OFF and disconnect the battery negative (-) cable. 2. Remove the rear seat (Refer to "Seat" in BD gro ...

Adjustment
1. After loosening the trunk lid hinge (A) mounting bolts, adjust the trunk lid by moving it up or down, or right or left. 2. Adjust the tr ...

Hyundai Accent Manuals


© 2011-2024 Copyright www.hamanual.com