Hyundai Accent Manuals

Hyundai Accent: Body Side Moldings. Repair procedures - Exterior - Body (Interior and Exterior)Hyundai Accent: Body Side Moldings. Repair procedures

Replacement

Trunk Lid Garnish Replacement
[Sedan]
•
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damaged.
•
Put on gloves to protect your hands.
•
Take care not to scratch the body surface.
1.
Remove the trunk lid trim.
(Refer to the BD group - "Trunk Lid")
2.
After loosening the mounting nuts, then remove the trunk lid garnish (A).

3.
Installation is the reverse of removal.
Rear Spoiler Replacement
[5 Door]
•
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damaged.
•
Put on gloves to protect your hands.
•
Take care not to scratch the body surface.
1.
Disconnect the rear spoiler connector (A) and washer nozzle (B).

2.
After loosening the mounting nuts, then remove the rear spoiler (A).

3.
Installation is the reverse of removal.
•
Replace any damage clips.
Roof Molding Replacement
•
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damaged.
•
Put on gloves to protect your hands.
•
Take care not to scratch the body surface.
1.
Using a screwdriver or remover, remove the roof molding (A).

2.
Installation is the reverse of removal.
•
Put on gloves to protect your hands.
•
Replace any damage clips.
Delta Garnish Replacement
•
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damaged.
•
Put on gloves to protect your hands.
•
Take care not to scratch the body surface.
1.
Using a screwdriver or remover, remove the delta garnish (A).

2.
Installation is the reverse of removal.
•
Replace any damage clips.
Quarter Garnish Replacement
[Sedan]
•
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damaged.
•
Put on gloves to protect your hands.
•
Take care not to scratch the body surface.
1.
Using a screwdriver or remover, remove the quarter garnish (A).

2.
Installation is the reverse of removal.
•
Replace any damage clips.
Front Wheel Guard Replacement
•
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damaged.
•
Put on gloves to protect your hands.
•
Take care not to scratch the body surface.
1.
Remove the front tire
2.
After loosening the mounting screws and nuts, then remove the front wheel guard (A).
[LH]

[RH]

3.
Installation is the reverse of removal.
•
Replace any damage clips.
Rear Wheel Guard and Mud Guard Replacement
•
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damaged.
•
Put on gloves to protect your hands.
•
Take care not to scratch the body surface.
1.
Remove the rear tire
2.
After loosening the mounting screws and nuts, then remove the rear wheel guard (A) and mud guard (B).

3.
Installation is the reverse of removal.
•
Replace any damage clips.
Deflector Guard Replacement
•
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damaged.
•
Put on gloves to protect your hands.
•
Take care not to scratch the body surface.
1.
Remove the rear tire.
2.
After loosening the mounting screws, then remove the deflecotor guard (A).

3.
Installation is the reverse of removal.
•
Replace any damage clips.

Adjustment
Glass Adjustment • Check the glass run channel for damage or deterioration, and replace ...

Sunroof. Components and Components Location
Components 1. Sunroof frame assembly 2. Motor assembly 3. Glass assembly 4. Guide assembly 5. Drip rail assembly 6. Drip link 7. Sunshade assembly 8. Defle ...

See also:

Disassembly
1. Remove the rear cover (A). 2. Loosen the mounting bolts(A) and disconnect the brush holder assembly(B). ...

Inspection
[Fuel pump] 1. Turn ignition switch OFF and disconnect the negative (-)battery cable. 2. Remove the fuel pump assembly. ...

Disassembly
1. Disconnect the M-terminal (A) on the magnet switchassembly. 2. After loosening the 2 screws (A), detach the magnetswitch assembl ...

Hyundai Accent Manuals


© 2011-2024 Copyright www.hamanual.com