|
1. |
Using a scerwdriver or remover, remove the front door quadrant
inner cover (A).
|
2. |
Disconnect the tweeter speaker connector (A).
|
3. |
After loosening the mounting screw, then remove the inside handle
housing (B).
|
4. |
After loosening the mounting screw, then remove the front door
trim (A).
|
5. |
Disconnect the power window connectors (A).
|
6. |
Installation is the reverse of removal.
|
1. |
Remove the front door trim
|
2. |
After loosening the mounting screws, then remove the inside handle
(A).
|
3. |
Disconnect the inside handle cable (A).
|
4. |
Installation is the reverse of removal.
|
1. |
Remove the front door trim.
|
2. |
After loosening the mounting screws, then remove the front door
seal (A).
|
3. |
Remove the front door belt inside weatherstrip (A).
|
4. |
Remove the front door belt outside weatherstrip (A).
|
5. |
Carefully adjust the glass (A) until you can see the screws, then
loosen them. Separate the glass from the glass run and carefully pull
the glass out through the window slot.
|
6. |
Installation is the reverse of removal.
|
1. |
Remove the front door trim.
|
2. |
Disconnect the speaker connector (B).
|
3. |
Drill out the rivets to remove the speaker (A).
|
4. |
Installation is the reverse of removal.
|
1. |
Remove the front door trim.
|
2. |
Remove the front door seal.
|
3. |
Remove the front door glass.
|
4. |
Disconnect the power window motor connector (B).
|
5. |
After loosening the mounting nuts, then remove the front door
power window regulator assembly (A).
|
6. |
After loosening the mounting screws, then remove the front door
power window moter (A).
|
7. |
Installation is the reverse of removal.
|
1. |
Remove the following parts :
|
2. |
Disconnect the outside handle rod (A).
|
3. |
Loosen the front door latch mounting screws.
|
4. |
Disconnect the front door latch connector (B).
|
5. |
After loosening the mounting screw, then remove the front door
latch (A).
|
6. |
Installation is the reverse of removal.
|
1. |
Remove the front door trim.
|
2. |
Remove the front door seal.
|
3. |
After loosening the mounting bolt, then remove the outside handle
cover (A).
|
4. |
Remove the outside handle (A) by sliding it rearward.
|
5. |
Disconnect the outside handle connector (A).
|
6. |
Installation is the reverse of removal.
|
1. |
Remove the front door trim.
|
2. |
Remove the front door seal.
|
3. |
After loosening the mounting bolt, then remove the outside handle
cover (A).
|
4. |
After loosening the mounting bolt, then disconnecting the rod
(A).
|
5. |
Installation is the reverse of removal.
|
1. |
Loosen the checker mounting bolts.
|
2. |
Detach the clips, then remove the front door weatherstrip (A).
|
3. |
Installation is the reverse of removal.
|
Troubleshooting
Troubleshooting
Problem Symptoms Table
Use the table below to help you find the cause of theproblem. The numbers
indicate the priority of the likecause of the problem. Check each p ...
To turn cruise control off, do one of the following
Push the cruise ON/OFF button (the CRUISE indicator light in the instrument
cluster will go off).
Turn the ignition off.
Both of these actions cancel cruise control operation. If you want ...
Carry emergency equipment
Depending on the severity of the weather where you drive your car, you should
carry appropriate emergency equipment. Some of the items you may want to carry include
tire chains, tow straps or chai ...