Hyundai Accent Manuals

Hyundai Accent: Specifications - Specifications - General Information - Automatic Transaxle System - Hyundai Accent 2010-2019 Service ManualHyundai Accent: Specifications

Item
Specifications
Transmission type
A6GF1
Engine model
Gasoline 1.6 GDI
Torque converter type
3-element, 1-stage, 2-phase type
Torque converter size
Ø225 mm (8.8583 in.)
Oil pump system
Parachoid
Friction elements
Clutch: 2EA
Brake: 3EA
OWC: 1EA
Planetary gear
 3EA
Gear ratio
1st
4.400
2nd
2.726
3rd
1.834
4th
1.392
5th
1.000
6th
0.772
Reverse
3.440
Final gear ratio
2.937
Fluid pressure balance piston
2EA
Accumulator
4EA
Solenoid valve
8EA (VFS:6EA, ON/OFF:2EA)
Shift lever position
 4 Range (P,R,N,D)
Oil filter
 1EA

VFS: Variable Force Solenoid
Sensors
Input Speed Sensor
▷ Type: Hall effect sensor
▷ Specifications
Operation condition (C)F
((-)40 ~ 150)) -40 ~ 302
Air gap(mm)in.
(1.2 ~ 1.8)
0.0472 ~ 0.0709
Output voltage(V)
High
1.18 ~ 1.68
Low
0.59 ~ 0.84

Output Speed Sensor
▷ Type: Hall effect sensor
▷ Specifications
Operation condition (C)F
((-)40 ~ 150)) -40 ~ 302
Air gap(mm)in.
(0.85 ~ 1.3)
0.033 ~ 0.051
Output voltage
High
1.18 ~ 1.68
Low
0.59 ~ 0.84

Oil Temperature Sensor
▷ Type: Negative thermal coefficient type
▷ Specifications
Temp.[(C)F]
Resistance (kΩ)
(-40)-40
48.1
(-20)-4.0
15.6
(0)32.0
5.88
(20)68.0
2.51
(40)104.0
1.19
(60)140.0
0.61
(80)176.0
0.32
(100)212.0
0.18
(120)248.0
0.10
(140)284.0
0.06
(150)302.0
0.05

Inhibitor Switch
▷ Type: Combination of output signals from 4 terminals
▷ Specifications
Power supply (V)
12
Output type
Combination of output signals

Solenoid Valves
Direct control VFS[26/B, T/CON]
▷ Control type : Normally low type
Control Pressure kpa (kgf/cm², psi)
9.81 ~ 500.14 (0.1 ~ 5.1, 1.42 ~ 72.54)
Current value(mA)
50 ~ 850
 Internal resistance(Ω)
5.1

Direct control VFS[UD/B, OD/C, 35R/C]
▷ Control Type : Normally high type
Control Pressure kpa (kgf/cm², psi)
500.14 ~ 9.81 (5.1 ~ 0.1, 72.54 ~ 1.42)
Current value(mA)
50 ~ 850
 Internal resistance(Ω)
5.1

Line Pressure Control VFS
▷ Control type : Normally high type
Control Pressure kpa (kgf/cm², psi)
500.14 ~ 9.81 (5.1 ~ 0.1, 72.54 ~ 1.42)
Current value(mA)
50 ~ 850
 Internal resistance(Ω)
5.1

ON/OFF Solenoid Valve(SS-A, SS-B)
▷ Control type : Normally low type
Control pressure kpa (kgf/cm², psi)
490.33(5.0, 71.12)
 Internal resistance(Ω)
10 ~ 11

Solenoid Valve Operation Table

SS-A
SS-B
UD/B-VFS
OD/C-VFS
35R/C-VFS
26/B-VFS
N/H
N/H
N/H
N/L
N, P






1
Δ


Δ


2






3






4






5






6






L






R







● : Connected status
Δ : Connected at vehicle speed above 8km/h
Tightening Torques
Item
 N.m
 Kgf.m
 lb-ft
TCM installation mounting bolt
9.8 ~ 11.8
1.0 ~ 1.2
7.2 ~ 8.7
Shift cable bracket mounting bolt
14.7 ~ 21.6
1.5 ~ 2.2
10.8 ~ 15.9
Input shaft speed sensor mounting bolt
9.8 ~ 11.8
1.0 ~ 1.2
7.2 ~ 8.7
Output shaft speed sensor mounting bolt
9.8 ~ 11.8
1.0 ~ 1.2
7.2 ~ 8.7
Shift lever assembly bolt
9.8 ~ 14.7
1.0 ~ 1.5
7.2 ~ 10.8
Inhibitor switch mounting bolt
9.8 ~ 11.8
1.0 ~ 1.2
7.2 ~ 8.7
Valve body cover mounting bolt
13.7 ~ 15.7
1.4 ~ 1.6
10.8 ~ 11.6
Eyebolt
2.9 ~ 4.9
0.3 ~ 0.5
2.2 ~ 3.6
Oil drain plug
38.2 ~ 48.1
3.9 ~ 4.9
28.2 ~ 35.4
Torque converter mounting bolt
45.1 ~ 52.0
4.6 ~ 5.3
33.3 ~ 38.3
Starter motor mounting bolt
42.2 ~ 53.9
4.3 ~ 5.5
31.1 ~ 39.8
Roll rod support bracket bolt
49.0 ~ 68.6
5.0 ~ 7.0
36.2 ~ 50.6
107.9 ~ 127.5
11.0 ~ 13.0
79.6 ~ 94.1
Automatic transaxle upper mounting bolt (TM=>Eng)
42.2 ~ 53.9
4.3 ~ 5.5
31.1 ~ 39.8
Automatic transaxle lower mounting bolt (Eng=>TM)
42.2 ~ 48.1
4.3 ~ 4.9
31.1 ~ 35.4
42.2 ~ 53.9
4.3 ~ 5.5
31.1 ~ 39.8
Automatic transaxle support bracket bolt
88.3 ~ 107.9
9.0 ~ 11.0
65.1 ~ 79.6


Specifications
...

Lubricants
Item  Specified lubricant  Quantity Transaxle fluid SK ATF SP-Ⅳ, MICHANG ATF SP-Ⅳ, NOCA ATF SP-Ⅳ, Hyunda ...

See also:

Don't let your parking brake freeze
Under some conditions your parking brake can freeze in the engaged position. This is most likely to happen when there is an accumulation of snow or ice around or near the rear brakes or if the bra ...

Closing the hood
1. Before closing the hood, check the following: All filler caps in engine compartment must be correctly installed. Gloves, rags or any other combustible material must be removed from the eng ...

Installation
When replacing the ECM, the vehicle equipped with the immobilizer must be performed procedure as below. [In the ...

Categories

Hyundai Accent Manuals

2011-2019 Copyright www.hamanual.com