Hyundai Accent: Front Seat Belt. Repair procedures
Replacement
Front Seat Belt Replacement
| •
|
When installing the belt, make sure not to damaged the
pretensioner.
|
|
|
1. |
Remove the following items first.
| A. |
Front seat assembly
(Refer to the BD group – “Front Seat”).
|
| B. |
Front door scuff trim and rear door scuff trim
(Refer to the BD group – “Interior Trim”).
|
|
|
2. |
Disconnect the battery negative cable, and wait for at least three
minutes before beginning work.
|
|
3. |
The seat belt anchor pretensioner (A) be removed after pushing
the lock pin (B) as arrow direction.
|
|
4. |
Using a screwdriver or remover, remove the center pillar lower
trim (A).
|
|
5. |
After loosening the mounting bolt, then remove the center pillar
upper trim (A).
|
|
6. |
Loosen the mounting bolt, then remove the front seat belt upper
anchor (A).
Tightening torque :
39.2~53.9 N.m (4.0~5.5 kgf.m, 28.9~39.8 lb-ft)
|
|
|
7. |
After disconnecting the pretensioner connector lock pin, remove
the BPT connector (A), Loosening the mounting bolt, then remove the
pretensioner (B).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)
|
|
|
8. |
Installation is the reverse of removal.
|
Hight Adjuster Replacement
|
1. |
Remove the following items first:
| A. |
Front door scuff trim and rear door scuff trim
(Refer to the BD group – “Interior Trim”).
|
| B. |
Front seat belt lower anchor.
|
| C. |
Center pillar lower trim.
(Refer to the BD group – “Interior Trim”).
|
| D. |
Center pillar upper trim
(Refer to the BD group – “Interior Trim”).
|
| E. |
Front seat belt upper anchor.
|
|
|
2. |
After loosening the bolts, then remove the hight adjustor (A).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)
|
|
|
3. |
Installation is the reverse of removal.
|
• |
Replace any damaged clips.
|
|
• |
Make sure the height adjust properly.
|
|
|
Front Seat Belt Buckle Replacement
|
1. |
Remove the following items first:
| A. |
Front seat assembly
(Refer to the BD group – “Front Seat”).
|
|
|
2. |
After loosening the mounting screws, then remove the front seat
track side cover (A).
|
|
3. |
Disconnect the connect (A) mounting clip.
|
|
4. |
After loosening the mounting bolt, then remove the front seat
belt buckle (A).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)
|
|
|
5. |
Installation is the reverse of removal.
|
Components
[Sedan]
1. Front seat belt
2. Height adjuster
3. Front seat belt anchor pretensioner
4. Rear seat belt
5. Rear center seat belt
6. Rear ...
Replacement
Rear Seat Belt Replacement
[Sedan]
•
When installing the belt, make s ...
See also:
Electronic stability control (ESC)
The Electronic Stability control (ESC) system is designed to stabilize the vehicle
during cornering maneuvers. ESC checks where you are steering and where the vehicle
is actually going. ESC appl ...
Rear Seat. Repair procedures
Replacement
Seat Assembly Replacement
1.
After loosening the mounting bolt, then remove the rear seat cushion
(A).
Tightening torque :
...
Airbag Module Disposal. Description
and Operation
Airbag Disposal
Special tool required
Deployment tool 0957A-34100A
Before scrapping any airbags or side airbags (including those in a whole
vehicle to be scrapped), the airbag ...
Components and Components Location
Rear Seat Belt. Repair procedures