Hyundai Accent: Rear Seat Belt. Repair proceduresReplacement
| [Sedan] | 
		
 
  | 
	
| 1. | 
		 
			Remove the following items first. 
		
 
  | 
	
| 2. | 
		 
			Using a screwdriver or remover, remove the rear pillar trim (A). 
		
		  | 
	
| 3. | 
		 
			After loosening the mounting screws and clips, then remove the 
			luggage partition trim (A). 
		
		  | 
	
| 4. | 
		 
			After loosening the mounting bolts, then remove the rear seat 
			bracket (A). 
		
		  | 
	
| 5. | 
		 
			After loosening the mounting clip, then remove the rear wheelhousing 
			trim (A). 
		
		  | 
	
| 6. | 
		 
			After loosening the mounting bolt, then remove the rear seat belt 
			lower anchor (A). 
		
 
		  | 
	
| 7. | 
		 
			Disconnect the connector (A). 
		
		  | 
	
| 8. | 
		 
			Remove the rear package tray trim (A). 
		
		  | 
	
| 9. | 
		 
			After loosening the retractor (B) mounting bolt, then remove the 
			rear seat belt (A). 
		
 
		  | 
	
| 10. | 
		 
			Installation is the reverse of removal. 
		
  | 
	
| [5 Door] | 
		
 
  | 
	
| 1. | 
		 
			Remove the rear seat. 
		
			(Refer to the BD group – “Rear Seat”) 
		 | 
	
| 2. | 
		 
			Remove the rear door scuff trim.  
		
		  | 
	
| 3. | 
		 
			Detach the mounting clips, remove the transverse trim (A). 
		
		  | 
	
| 4. | 
		 
			After loosening the mounting bolt, then remove the rear seat belt 
			lower anchor (A). 
		
 
		  | 
	
| 5. | 
		 
			After loosening the mounting bolts, then remove the rear seat 
			bracket (A). 
		
		  | 
	
| 6. | 
		 
			Using a screwdriver or remover, remove the lamp (A). 
		 | 
	
| 7. | 
		 
			Disconnect the connector (B). 
		 | 
	
| 8. | 
		 
			After loosening the mounting screws, then remove the luggage side 
			trim (C). 
		
		  | 
	
| 9. | 
		 
			Remove the rear seat belt upper anchor cover (B). 
		 
		 | 
	
| 10. | 
		 
			After loosening the mounting bolts, then remove the rear pillar 
			trim (A). 
		
		  | 
	
| 11. | 
		 
			After loosening the retractor (B) mounting bolts, then remove 
			the rear seat belt (A). 
		
 
		  | 
	
| 12. | 
		 
			Installation is the reverse of removal. 
		
  | 
	
		
 
  | 
	
| 1. | 
		 
			Remove the following items first. 
		
 
 
  | 
	
| 2. | 
		 
			The rear center seat belt buckle (A) be removed after pushing 
			the lock pin (B) as arrow direction. 
		
		  | 
	
| 3. | 
		 
			After loosening the mounting bolt, then remove the seat belt center 
			upper anchor (A). 
		
 
		  | 
	
| 4. | 
		 
			After loosening the mounting nut, then remove the seat belt center 
			retrator (A). 
		
 
		  | 
	
| 5. | 
		 
			Installation is the reverse of removal. 
		 | 
	
| 1. | 
		 
			Remove the rear seat. 
		
			(Refer to the BD group - "Rear Seat") 
		 | 
	
| 2. | 
		 
			Loosen the mounting bolt, and then remove the rear seat belt buckle 
			(A). 
		
 
			[ LH ]  
		
		 
			[ RH ]  
		
		  | 
	
| 3. | 
		 
			Installation is the reverse of removal. 
		 | 
	
Front Seat Belt. Repair proceduresConsole. Repair procedures
   Replacement
	Floor Console Replacement 
	
		[ M/T ]
	
	
		
		
			
				
				
			
			
				
				
			
		
		
			
				•
				
				
				
					When prying with a flat-tip screw ...
   
Interior B ( 4Door )
   
	
		
		
		
		
		
		
		
		
		
		
		
		
	
	
		
		Seatbelt height adjust upper mounting hole (Ø15)
		
		
		Seatbelt height adjust lower mounting hole (Ø15)
		
		
 ...
   
Removal
   
	
		
		
			
				
				
			
			
				
				
			
		
		
			When replacing the ECM, the vehicle equipped with 
			the immobilizer must be performed procedure as below.
		
		
		
			[In the ...