Hyundai Accent Manuals

Hyundai Accent: Replacement - Rear Hub - Carrier. Repair procedures - Rear Axle Assembly - Driveshaft and axleHyundai Accent: Replacement

Hyundai Accent RB (2010-2018) Service Manual / Driveshaft and axle / Rear Axle Assembly / Rear Hub - Carrier. Repair procedures / Replacement

[Disc Type]

1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the rear wheel and tire (A) from rear hub .
Tightening torque:
88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)

Be careful not to damage to the hub bolts when removing the rear wheel and tire (A).
3.
Remove the clip (A) and then remove the parking brake cable (B).
4.
Remove the brake caliper mounting bolts, and then place the brake caliper assembly (B) with wire.
Tightening torque:
63.7 ~ 73.5 N.m (6.5 ~ 7.5 kgf.m, 47.0 ~ 54.2 lb-ft)

5.
Loosen the mounting screws and then brake disc (A).
Tightening torque:
4.9 ~ 5.8 N.m (0.5 ~ 0.6 kgf.m, 3.6 ~ 4.3 lb-ft)

6.
Loosen the hub mounting bolt and then remove the hub (A) from torsion beam axle.
Tightening torque:
49.0 ~ 58.8 N.m (5.0 ~ 6.0 kgf.m, 36.1 ~ 43.3 lb-ft)

7.
Install in the reverse order of removal.
[Drum Type]
1.
Remove the rear wheel & tire.
Tightening torque:
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

2.
Loosen the screw (A) and then remove the disc (B).
Tightening torque:
4.9 ~ 5.8 N.m (0.5 ~ 0.6 kgf.m, 3.6 ~ 4.3 lb-ft)

3.
Remove the spring (A, B, C).
4.
Remove the shoe (A).
5.
Disconnect the parking brake cable (A) from lining (B).
6.
Remove the clip (A).
7.
Remove the parking brake cable clip (A).
8.
Loosen the wheel speed sensor cable (A) bolt &nut and parking brake cable (B) mounting nut.
9.
Remove the brake hose (A) and then loosen the cylinder bolt.
10.
Loosen the hub mounting bolt and then remove the hub (A) from the torsion beam.
Tightening torque:
49.0 ~ 58.8 N.m (5.0 ~ 6.0 kgf.m, 36.2 ~ 43.4 lb-ft)

11.
Install in the reverse order of removal.

Rear Hub - Carrier. Repair procedures
...

Inspection
1. Check the hub for cracks and the splines for wear. 2. Check the brake disc for scoring and damage. 3. C ...

See also:

Relay Box (Engine Compartment). Repair procedures
Inspection Power Relay Test (Type A) - Do not use pliers. - ...

Input Speed Sensor. Description and Operation
Description Input speed sensor (A) is a vital unit that measures the rate of rotation of the input shaft inside the transaxle and delivers the readings to the TCM. The sensor provides critic ...

SRSCM Connector terminal
Pin Function (Connector A) Pin Function (Connector B) 1 Ignition 1 Seat belt pretensioner [Drive ...

Hyundai Accent Manuals

В© 2011-2026 Copyright www.hamanual.com