Hyundai Accent: Description and Operation
Hyundai Accent RB (2010-2018) Service Manual / Restraint (Advanced) / General Information / Description and Operation
Warning Lamp Activation
| Warning Lamp Behavior after Ignition On |
As soon as the operating voltage is applied to the SRSCM ignition input,
the SRSCM activates the warning lamp for a LED lamp check.
The lamp shall turn on for 6 seconds during the initialization phase and
be turned off afterward.
To alert the driver, the warning lamp shall turn on for 6 seconds and
off for one second then on continuously after the operating voltage is applied
if any active fault exists.
| 1. |
Active faults exist.
|
| 2. |
No active faults or crash records exists.
|
| 3. |
When turning the ignition switch ON during variant coding (EOL)
mode, the airbag warning lamp is turned on and blinks at intervals of
1 second till the coding is completed.
In case the variant coding is normally completed, the airbag warning
lamp is turned on for 6 seconds, and then turned off. Otherwise the
airbag warning lamp continuously blinks at intervals of 1 second.
When there is active fault in airbag system or SRSCM internal
fault, the variant coding (EOL) can’t be completed. In this case, do
the variant coding (EOL) procedure again after troubleshooting with
the GDS.
|
SRSCM Independent Warning Lamp Activation
There are certain fault conditions in which the SRSCM cannot function
and thus cannot control the operation of the airbag warning lamp. In these cases,
the airbag warning lamp is directly activated by appropriate circuitry that
operates independently of the SRSCM. These cases are:
| 1. |
Loss of battery supply to the SRSCM : warning lamp turned on continuously.
|
| 2. |
Loss of internal operating voltage : warning lamp turned on continuously.
|
| 3. |
Loss of Microprocessor operation : warning lamp turned on continuously.
|
| 4. |
SRSCM not connected : warning lamp turned on continuously.
|
Telltale Lamp Activation
The Telltale Lamp indicates the Passenger Airbag(PAB) enabled and disabled
status based on occupant status of passenger seat. If the passenger seat is
empty or occupied with child (or child seat), the Passenger Airbag is disabled
and the Telltale Lamp is turned ON to inform the driver that the PAB is disabled.
As soon as operating voltage is applied to the SRSCM ignition input, the SRSCM
activates telltale lamp prove out. ODS (Occupant Detection System) will send
an indeterminate status to the SRSCM as a default setting for passenger airbag
deployment during the prove out period.
After ignition on, telltale lamp will turn on for 4 seconds and turn off
for 3 seconds during the initialization phase and be turned ON afterward until
receipt of valid enabled message from ODS system.
General Safety Information and
Caution
Precautions
General Precautions
Please read the following precautions carefully before performing the
airbag system service.
Observe the instructions described in this manual, ...
Repair procedures
Component Replacement After Deployment
Before doing any SRS repairs, use the GDS to check for DTCs. Refer
to the Diagnostic Tr ...
See also:
Speed sensing door lock system
All doors will be automatically locked after the vehicle speed exceeds 9 mph
(15 km/h). And all doors will be automatically unlocked when you turn the engine
off or when you remove the ignition ke ...
Fuel requirements
Your new vehicle is designed to use only unleaded fuel having a pump octane number
((R+M)/2) of 87 (Research Octane Number 91) or higher.
Your new vehicle is designed to obtain maximum performance ...
ETC (Electronic Throttle
Control) System. Schematic Diagrams
Circuit Diagram
(M/T)
(A/T)
...
Hyundai Accent Manuals
- Hyundai Accent 2017-2022 Service Manual
- Hyundai Accent 2010-2025 Owners Manual
- Hyundai Accent 2010-2025 Service Manual
В© 2011-2025 Copyright www.hamanual.com