Hyundai Accent Manuals

Hyundai Accent: Rear Seat. Repair procedures - Seat & Power Seat - Body (Interior and Exterior)Hyundai Accent: Rear Seat. Repair procedures

Hyundai Accent RB (2010-2018) Service Manual / Body (Interior and Exterior) / Seat & Power Seat / Rear Seat. Repair procedures

Replacement

Seat Assembly Replacement
1.
After loosening the mounting bolt, then remove the rear seat cushion (A).
Tightening torque :
16.7 ~ 25.5 N.m (1.7 ~ 2.6 kgf.m, 12.3 ~18.8 lb-ft)

2.
The rear center seat belt buckle (A) be removed after pushing the lock pin (B) as arrow direction.
3.
After loosening the mounting bolts, then remove the rear seat back (A).
Tightening torque :
16.7 ~ 25.5 N.m (1.7 ~ 2.6 kgf.m, 12.3 ~18.8 lb-ft)

4.
Installation is the reverse of removal.
Rear Seat Back Cover Replacement [LH]
[Sedan]
•
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damaged.
•
Put on gloves to protect your hands.
1.
Remove the rear seat assembly.
2.
Push the lock pin (B) and then remove the headrest (A).
3.
After loosening the mounting screw, then remove the rear seat back webbing guide (A).
4.
Remove the rear seat folding lever (A) after turning in the counter clock-wise direction.
5.
Remove the rear seat folding lever cover (B).
6.
Remove the rear seat back cover (A).
7.
Using a screwdriver or remover, remove the seat back cover (A).
8.
Disconnect the protector (A).
9.
Pull out the headrest guides (A) while pinching the end of the guides, and remove them.
10.
Remove the rear seat back cover from the rear seat back frame.
11.
After removing the velcro tape (B) on the front of seat cushion and remove the seat cushion cover (A).
12.
Installation is the reverse of removal.
•
Replace any damaged clips.
Rear Seat Back Cover Replacement [LH]
[5 Door]
•
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damaged.
•
Put on gloves to protect your hands.
1.
Remove the rear seat assembly.
2.
Push the lock pin (B) and then remove the headrest (A).
3.
Remove the rear seat belt cover (A).
4.
Remove the rear seat folding lever (A) after turning in the counter clock-wise direction.
5.
After loosening the mounting screws, then remove the rear seat latch cover (A).
6.
Remove the rear seat back cover (A).
7.
Using a screwdriver or remover, remove the seat back cover (A).
8.
Disconnect the protector (A).
9.
Pull out the headrest guides (A) and rear seat folding lever cover (B) while pinching the end of the guides, and remove them.
10.
Remove the rear seat back cover (A) from the rear seat back frame (B).
11.
After removing the velcro tape (B) on the front of seat cushion and remove the seat cushion cover (A).
12.
Installation is the reverse of removal.
•
Replace any damaged clips.
Rear Seat Latch Replacement [LH]
[Sedan]
•
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damaged.
•
Put on gloves to protect your hands.
1.
Remove the seat back cover.
2.
Remove the rear seat folding lever (A) after turning in the counter clock-wise direction.
3.
Remove the rear seat folding lever cover (B).
4.
After loosening the mounting bolts and then remove the rear seat latch (A).
5.
Installation is the reverse of removal.
Rear Seat Latch Replacement [LH]
[5 Door]
•
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damaged.
•
Put on gloves to protect your hands.
1.
Remove the seat back cover.
2.
Remove the rear seat folding lever (A) after turning in the counter clock-wise direction.
3.
Remove the rear seat folding lever cover (A).
4.
After loosening the mounting bolts and then remove the rear seat latch (A).
5.
Installation is the reverse of removal.
Rear Seat Back Cover Replacement [RH]
[Sedan]
•
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damaged.
•
Put on gloves to protect your hands.
1.
Remove the rear seat assembly.
2.
Push the lock pin (B) and then remove the headrest (A).
3.
After loosening the mounting screw, then remove the rear seat back webbing guide (A).
4.
Remove the rear seat folding lever (A) after turning in the counter clock-wise direction.
5.
Remove the rear seat folding lever cover (B).
6.
Remove the rear seat back cover (A).
7.
Using a screwdriver or remover, remove the seat back cover (A).
8.
Disconnect the protector (A).
9.
Pull out the headrest guides (A) while pinching the end of the guides, and remove them.
10.
Remove the rear seat back cover from the rear seat back frame.
11.
After removing the velcro tape (B) on the front of seat cushion and remove the seat cushion cover (A).
12.
Installation is the reverse of removal.
•
Replace any damaged clips.
Rear Seat Back Cover Replacement [RH]
[5 Door]
•
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damaged.
•
Put on gloves to protect your hands.
1.
Remove the rear seat assembly.
2.
Push the lock pin (B) and then remove the headrest (A).
3.
Remove the rear seat folding lever (A) after turning in the counter clock-wise direction.
4.
After loosening the mounting screw, then remove the rear seat latch cover (A).
5.
Remove the rear seat back cover (A).
6.
Using a screwdriver or remover, remove the seat back cover (A).
7.
Disconnect the protector (A).
8.
Pull out the headrest guides (A) and rear seat folding lever cover (B) while pinching the end of the guides, and remove them.
9.
Remove the rear seat back cover from the rear seat back frame.
10.
After removing the velcro tape (B) on the front of seat cushion and remove the seat cushion cover (A).
11.
Installation is the reverse of removal.
•
Replace any damaged clips.
Rear Seat Latch Replacement [RH]
[Sedan]
•
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damaged.
•
Put on gloves to protect your hands.
1.
Remove the seat back cover.
2.
Remove the rear seat folding lever (A) after turning in the counter clock-wise direction.
3.
Remove the rear seat folding lever cover (B).
4.
After loosening the mounting bolts and then remove the rear seat latch (A).
5.
Installation is the reverse of removal.
Rear Seat Latch Replacement [RH]
[5 Door]
•
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damaged.
•
Put on gloves to protect your hands.
1.
Remove the seat back cover.
2.
Remove the rear seat folding lever (A) after turning in the counter clock-wise direction.
3.
Remove the rear seat folding lever cover (A).
4.
After loosening the mounting bolts and then remove the rear seat latch (A).
5.
Installation is the reverse of removal.
Rear Seat Cushion Cover Replacement
•
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damaged.
•
Put on gloves to protect your hands.
1.
Remove the rear seat cushion.
2.
Remove the hog-ring clips (A).
3.
Disconnect the hog-ring clips (B) on the rear of seat cushion, remove the seat cushion cover (A).
4.
Installation is the reverse of removal.
•
To prevent wrinkles, make sure the material is stretched evenly over the cover (B) before securing the hog-ring clips (A).
•
Replace the hog-ring clips with new ones using special tool [C (09880-4F000)].


Rear Seat. Components and Components Location
Components 1. Headrest [RH] 2. Rear seat back cover [RH] 3. Rear seat back frame assembly [RH] 4. Rear back cover [RH] 5. Headrest [Center] 6. Headrest [LH] 7 ...

Seat Belt
...

See also:

Removal
1. Remove the mounting bolt and disconnect the horn connector, then remove the horn (A). ...

Certification label
The certification label is located on the driver's door sill at the center pillar. This label shows the maximum allowable weight of the fully loaded vehicle. This is called the GVWR (Gross Ve ...

Steering Gear box. Components and Components Location
Components 1. Tie-rod end 2. Lock nut 3. Bellows clip 4. Bellows 5. Tie rod 6. Rack bar 7. Dust packing 8. Dust cap 9. Oil seal 10. Pinion plug ...

Hyundai Accent Manuals

© 2011-2026 Copyright www.hamanual.com