Hyundai Accent Manuals

Hyundai Accent: Replacement - Front Hub / Knuckle. Repair procedures - Front Axle Assembly - Driveshaft and axleHyundai Accent: Replacement

Hyundai Accent RB (2010-2018) Service Manual / Driveshaft and axle / Front Axle Assembly / Front Hub / Knuckle. Repair procedures / Replacement

1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the front wheel and tire (A) from front hub .
Tightening torque:
88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)

Be careful not to damage to the hub bolts when removing the front wheel and tire (A).
3.
Remove the brake caliper mounting bolts , and then hold the brake caliper assembly (B) with wire.
Tightening torque:
78.4 ~ 98.0 N.m (8.0 ~ 10.0 kgf.m, 57.8 ~ 72.3 lb-ft)

4.
Remove the brake hose mounting bracket (A) & wheel speed sensor (B) & bracket (C).
Tightening torque (B,C):
7.8 ~ 11.8 N.m (0.8 ~ 1.2 kgf.m, 5.8 ~ 8.7 lb-ft)

5.
Remove driveshaft nut (A) from the front hub under applying the brake.
Tightening torque:
196.1 ~ 274.5 N.m (20.0 ~ 28.0 kgf.m, 144.6 ~ 202.5 lb-ft)

-
The driveshaft lock nut should be replaced with new ones.
-
After installation driveshaft lock nut, stake the lock nut using a chisel and hammer as shown in the illustration below.

6.
Remove the tie rod end ball joint from the knuckle.
(1)
Remove the split pin (A).
(2)
Remove the castle nut (B).
Tightening torque:
23.5 ~ 33.3 N.m (2.4 ~ 3.4 kgf.m, 19.4 ~ 24.5 lb-ft)

7.
Remove the lower arm (A) from the knuckle.
Tightening torque:
196.1 ~ 274.5 N.m (6.0 ~ 7.2 kgf.m, 144.6 ~ 202.5 lb-ft)

8.
Disconnect the driveshaft (A) from the front hub assembly.
9.
Loosen the strut mounting bolts and then remove the knuckle assembly (A).
Tightening torque:
137.3 ~ 156.9 N.m (14.0 ~ 16.0 kgf.m, 101.3 ~ 115.7 lb-ft)

10.
Install in the reverse order of removal.

Front Hub / Knuckle. Repair procedures
...

Disassembly
1. Remove the snap ring (A). 2. Remove the hub assembly from the knuckle assembly. (1) Install the ...

See also:

Front fog light
Fog lights are used to provide improved visibility when visibility is poor due to fog, rain or snow etc. The fog lights will turn on when fog light switch (1) is turned to ON after the headlight ...

Description and Operation
Description The starting system includes the battery, starter, solenoid switch, inhibitor switch (A/T), ignition switch, ignition lock switch, connection wires and the battery cable. Whe ...

Certification label
The certification label is located on the driver's door sill at the center pillar. This label shows the maximum allowable weight of the fully loaded vehicle. This is called the GVWR (Gross Ve ...

Hyundai Accent Manuals

В© 2011-2026 Copyright www.hamanual.com