Hyundai Accent Manuals

Hyundai Accent: Replacement - Front Door. Repair procedures - Exterior - Body (Interior and Exterior)Hyundai Accent: Replacement

Hyundai Accent RB (2010-2018) Service Manual / Body (Interior and Exterior) / Exterior / Front Door. Repair procedures / Replacement

Front Door Trim Replacement
•
Be careful not to scratch the door trim and other parts.
•
Put on gloves to protect your hands.
1.
Using a scerwdriver or remover, remove the front door quadrant inner cover (A).
2.
Disconnect the tweeter speaker connector (A).
3.
After loosening the mounting screw, then remove the inside handle housing (B).
4.
After loosening the mounting screw, then remove the front door trim (A).
5.
Disconnect the power window connectors (A).
6.
Installation is the reverse of removal.
•
Make sure connectors are connected properly and each rod is connected securely.
•
Make sure the door locks/unlocks and opens/closes properly.
•
Replace any damaged clips.
Inside Handle Replacement
1.
Remove the front door trim
2.
After loosening the mounting screws, then remove the inside handle (A).
3.
Disconnect the inside handle cable (A).
4.
Installation is the reverse of removal.
•
Make sure the door locks/unlocks and opens/closes properly.
•
Replace ant damaged clips.
Glass Replacement
1.
Remove the front door trim.
2.
After loosening the mounting screws, then remove the front door seal (A).
•
Replace any damaged door seal.

3.
Remove the front door belt inside weatherstrip (A).
4.
Remove the front door belt outside weatherstrip (A).
•
Front door belt outside weatherstrip is need to changed to new product surely.

5.
Carefully adjust the glass (A) until you can see the screws, then loosen them. Separate the glass from the glass run and carefully pull the glass out through the window slot.
Tightening torque :
3.9 ~ 5.9 N.m (0.4 ~ 0.6 kgf.m, 2.9 ~ 4.3 lb-ft)

6.
Installation is the reverse of removal.
•
Roll the glass up and down to see if it move freely without binding.
•
Adjust glass position as needed.
Speaker Replacement
1.
Remove the front door trim.
2.
Disconnect the speaker connector (B).
3.
Drill out the rivets to remove the speaker (A).
4.
Installation is the reverse of removal.
•
Use sheet metal screws to secure the speaker.
•
Replace any damaged clips.
•
Make sure the door locks/unlocks and opens/closes properly.
•
Make sure connectors are connected properly and each rod is connected securely.
Power Window Motor Replacement
1.
Remove the front door trim.
2.
Remove the front door seal.
3.
Remove the front door glass.
4.
Disconnect the power window motor connector (B).
5.
After loosening the mounting nuts, then remove the front door power window regulator assembly (A).
Tightening torque :
3.9 ~ 5.9 N.m (0.4 ~ 0.6 kgf.m, 2.9 ~ 4.3 lb-ft)

6.
After loosening the mounting screws, then remove the front door power window moter (A).
7.
Installation is the reverse of removal.
•
Grease should be applied to areas where there is rotational parts and springs.
•
Roll the glass up and down to see if it move freely without binding.
Door Latch Replacement
1.
Remove the following parts :
A.
Front door trim
B.
Front door seal
C.
Front door glass
2.
Disconnect the outside handle rod (A).
3.
Loosen the front door latch mounting screws.
Tightening torque :
7.8 ~ 10.8 N.m (0.8 ~ 1.1 kgf.m, 5.8 ~ 8.0 lb-ft)

4.
Disconnect the front door latch connector (B).
5.
After loosening the mounting screw, then remove the front door latch (A).
6.
Installation is the reverse of removal.
•
Make sure the door locks/unlocks and opens/closes properly.
•
Replace any damage clips.
Outside Handle Replacement
1.
Remove the front door trim.
2.
Remove the front door seal.
3.
After loosening the mounting bolt, then remove the outside handle cover (A).
Tightening torque :
6.9~10.8 N.m (0.7~1.1 kgf.m, 5.1~8.0 lb-ft)

4.
Remove the outside handle (A) by sliding it rearward.
5.
Disconnect the outside handle connector (A).
6.
Installation is the reverse of removal.
•
Make sure the door locks/unlocks and opens/closes properly.
•
Replace any damage clips.
Key Holder Replacement
1.
Remove the front door trim.
2.
Remove the front door seal.
3.
After loosening the mounting bolt, then remove the outside handle cover (A).
Tightening torque :
6.9~10.8 N.m (0.7~1.1 kgf.m, 5.1~8.0 lb-ft)

4.
After loosening the mounting bolt, then disconnecting the rod (A).
5.
Installation is the reverse of removal.
Door Weatherstrip Replacement
1.
Loosen the checker mounting bolts.
2.
Detach the clips, then remove the front door weatherstrip (A).
3.
Installation is the reverse of removal.

Front Door. Repair procedures
...

Adjustment
Glass Adjustment • Check the glass run channel for damage or deterioration, and replace ...

See also:

To cancel cruise control, do one of the following
Press the brake pedal. Press the clutch pedal with a manual transaxle. Shift the shift lever into N (Neutral) with an automatic transaxle Press the CANCEL switch located on the steering whe ...

Front Body E ( 5Door )
Hood hinge mounting hole (Ø10) Fender apron upper member tooling hole (Ø6.6) Cowl under ...

Disassembly
Engine removal is required for this procedure. (Refer to Engine and transaxle assembly removal in this group) 1. M/T : Remove the fly wheel. 2. ...

Hyundai Accent Manuals

© 2011-2026 Copyright www.hamanual.com