Hyundai Accent Manuals

Hyundai Accent: Replacement - Rear Hub - Carrier. Repair procedures - Rear Axle Assembly - Driveshaft and axleHyundai Accent: Replacement

Hyundai Accent RB (2010-2018) Service Manual / Driveshaft and axle / Rear Axle Assembly / Rear Hub - Carrier. Repair procedures / Replacement

[Disc Type]

1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the rear wheel and tire (A) from rear hub .
Tightening torque:
88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)

Be careful not to damage to the hub bolts when removing the rear wheel and tire (A).
3.
Remove the clip (A) and then remove the parking brake cable (B).
4.
Remove the brake caliper mounting bolts, and then place the brake caliper assembly (B) with wire.
Tightening torque:
63.7 ~ 73.5 N.m (6.5 ~ 7.5 kgf.m, 47.0 ~ 54.2 lb-ft)

5.
Loosen the mounting screws and then brake disc (A).
Tightening torque:
4.9 ~ 5.8 N.m (0.5 ~ 0.6 kgf.m, 3.6 ~ 4.3 lb-ft)

6.
Loosen the hub mounting bolt and then remove the hub (A) from torsion beam axle.
Tightening torque:
49.0 ~ 58.8 N.m (5.0 ~ 6.0 kgf.m, 36.1 ~ 43.3 lb-ft)

7.
Install in the reverse order of removal.
[Drum Type]
1.
Remove the rear wheel & tire.
Tightening torque:
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

2.
Loosen the screw (A) and then remove the disc (B).
Tightening torque:
4.9 ~ 5.8 N.m (0.5 ~ 0.6 kgf.m, 3.6 ~ 4.3 lb-ft)

3.
Remove the spring (A, B, C).
4.
Remove the shoe (A).
5.
Disconnect the parking brake cable (A) from lining (B).
6.
Remove the clip (A).
7.
Remove the parking brake cable clip (A).
8.
Loosen the wheel speed sensor cable (A) bolt &nut and parking brake cable (B) mounting nut.
9.
Remove the brake hose (A) and then loosen the cylinder bolt.
10.
Loosen the hub mounting bolt and then remove the hub (A) from the torsion beam.
Tightening torque:
49.0 ~ 58.8 N.m (5.0 ~ 6.0 kgf.m, 36.2 ~ 43.4 lb-ft)

11.
Install in the reverse order of removal.

Rear Hub - Carrier. Repair procedures
...

Inspection
1. Check the hub for cracks and the splines for wear. 2. Check the brake disc for scoring and damage. 3. C ...

See also:

Repair procedures
Inspection [System Inspection] 1. Disconnect the vapor hose from the intake manifold and connect a vacuum pump to the nipple on the intake manifold. · At Col ...

Torque Converter Control Solenoid Valve (T/CON_VFS). Specifications
Specifications Direct control VFS[T/CON] ▷ Control type : Normal low type Control Pressure kpa (kgf/cm², psi) 9.81 ~ 500.14 (0.1 ~ 5.5, 1.42 ~ 7.82) ...

General Information
General The supplemental restraint system (SRS) is designed to supplement the seat belt to help reduce the risk or severity of injury to the driver and passenger by activating and deploying ...

Hyundai Accent Manuals

© 2011-2026 Copyright www.hamanual.com